Home Use Teeth Whitening |  Temporary Crown Materials | The Oral Moisture Barrier Materi | Twin-Compressors of Aluminum | Vacuum Former | Vacuum MIxer | Wax Pot | Zirconia Block | Zirconia Sintering Furnace | Ultrasonic Cleaner | Universal Barrier Film | Weak Straw | Ultrasonic Scaler | Teeth Whitening | Magnetic Denture Articulators | Model Arch Trimmer | Nail Class | Plaster Vibrator | Plastic Board Pin | Pure Titanium Casting Machine Sy | Resin Teeth | Rotatable Gas Light | Single Compressore | Sealing Machine | Steam Autoclave(Sterilizer) | Sterilization Instructions Suppl | Sterilization Pouches | Strong Straw | Non Woven Dressing | Prophy Angle | Prophy Brush | Prophy Cup | Occlusal Recording Material | Post and Core Material | Root Canal Post | Oral Anaesthetic Equipment | Paste carriers | Peeso Reamers | Pluggers | Reamers | Short Barbed Broaches | Spreader | SuperFiles | RA Diamond Dental Bur | Sintered Dental Bur | Steel Burs | Sand Blasting Powder | Sandblasting Scaler | Scaler Tips

DH-08S Automatic Sealing Machine

2012052464528765

 

 

Detailed Description

  1. Propose

DH-08S Automatic Sealing Machine is a special appliance use for thermoplastic package sealing,

  1. Speciality

The product use the thermo and mechanical drive to sealing the package automatic
The temperature controller has two model for MANUAL and AUTO
The product made with modern design and best material

3. Constitute
The DH-08S Auotmatic Sealing Machine compose of the shell, heating system, temperature contoll system, drive system and exhaust fan.

  1. Techician Parameters

Safety class: class I appliance
Power supply: A.C.220V±22V  ,50HZ±1HZ,Total power:300W
Unpitched sound lower than 60db
Outline Dimension: 300×230×130
Net Weight: 8KG

  1. Storage Condition

Temperature:-40℃~55℃
Humidity: ≤90%
Air Pressure: 80kPa-106kPa

  1. Working Condition

Temperature: above 10℃
Humidity: ≤90%
Air Pressure: 80kPa-106kPa

  1. Installtion guide

Put the machine on the platform, use with the paper cutter

8. Safety Notice:
1. The shell for machine body should be ground firmly.
2. Please take the bottom for the machine when you move the sealer

9. Operation
A. Conjunction with the power, open the switch, the heater on, adjust the temperature according to the materials sealed, (recommend temperature between the 190℃-220℃,) when the temperature reach at the setting temperature, the sealing word can be start.
B. Put the package plastic on the up side, Roll from the left to right smoothly.
C. Check the quality of sealed package, and repeat the cycle.
D. Discover any anomaly, please cut the power, after the problem solve, the operation can be start.

10. Temperature controller setting
Main control setting
Under the normal measurement, Long press ▲or▼for,The SP display with it in turn, this value is main control setting value, if you need to amend this value, you can press the ▲or▼(the temperature will be change fast by long press)

  1. Inner parameters setting.

Press the ▲or▼ at the same time, you will enter the Inner parameters setting (Reference as follow form).the parameter signal and valve alternate display, this value can be change by press the ▲or▼ key, (long press can change the value fast), when the setting finished, press the ▲or▼ in the same time enter into next setting, the same way to setting other parameters, It will auto saved and back to normal measurements after the digital flash 8 times when no operation make

No. Prompt Name Scope Description Factory
value
0 AP Main control setting All scope Long Press ▲or▼ key to setting Random
1 AL Limited Alarm All scope When the temperature over the limited ,the alarm on Random
2 SC Measure deviations ±20 Correct the measure deviations, 0
3 P proportional band 0-125
(the user was prohibited to setting above 100)
Proportional band=P×20,it will determine the system proportion gain, P more higher, the effect of proportional band will lower, overshoot will lower, but it will effect the heating time, setting the P=0,the meter transfer to two position control sate 8
4 1 Integral time 0-999s Setting the Integral time, to unlock the proportion control makes residual standard deviation, High value will delay the system reach the balance time, low value will arise the fluctuation 240
5 d derivative time 0-250s Setting the derivative time, prevent to the fluctuation of output, arise the control stabilization 30
6 t Control circle 1-120s 10
7 Hy Main Control Hystersis 0.1-50 Only effect in two position control 0.1

We are Dental Periodontal | Dental Restorations | Dental Sanitary | Dental Laboratory Rubber Diamond | Dental Laboratory Rubber Polishe | Dental Laboratory Silicone Diamo | Dental Laboratory Silicone Polis | Dental Laser | Dental Unit | Dental X-ray | Dental Material | Dental Silicon Impression Materi | Dental Visualizer | Double-pen Electric Wax Knife | Dust Collection Unit | Flame Torch | Grinding Polishing Material | High Speed Alloy Grinder | Lab Polishing Brush | Laser Pin | Dental Micro Applicator | Endodontic Treatment | Gates Drills | Gutta Percha Obturation | Gutta Percha Points | H-files | Dental Orthodontic Instruments | Dental Periodontal Instruments | Dental Abrasive Tool | Dental Clinical Equipments | Dental Endodontics | Dental Handpiece | Dental Infection Prevention | Dental Instruments | Dental Laboratory | 3-way Syringe | Dental Bib | Dental Cotton Roll | Adhesive & Curing Light | Amalgam Alloy | Amalgamator | Blasting Guns | Clinical Use Teeth Whitening | Dental Planting Instruments | Dental Repair Instruments | Dental Surgical Instruments | Dental Therapeutic Instruments | Dental Sterilizer Series | Disinfection Box | Handpiece Maintenance | Handpiece Spare Part | High Speed Handpiece | Low Speed Handpiece,manufacturers in China.Unified Wholesale price.Welcome to inquiry and OEM.

Have any question, Please enter the form below and click the submit button.


*
*
*
*
3 + 4 = ?
Please enter the answer to the sum & Click Submit to verify your registration.
CATEGORY AND TAGS:

Sealing Machine

Related Items

  • Product Categories